Updated Nov 21, 2026· 9 min read

Key takeaways

  • Compare the best Zigbee and Z-Wave smart relays from Zooz, Aqara and MHCOZY: in-wall modules, dry contacts for garage doors, gates and boilers.

Table of Contents

  • Quick Answer
  • Zooz ZEN51 Dry Contact Relay
  • Zooz ZEN17 800LR Universal Relay
  • Zooz ZEN16 MultiRelay
  • Aqara Dual Relay Module T2
  • MHCOZY 1-Channel ZigBee Smart Relay Switch
  • How to Choose
  • Who Should Skip
  • FAQ
  • Final Verdict
  • Product and ASIN Reference

A smart switch replaces the switch on your wall. A smart relay does something more flexible: it hides behind the switch you already own or next to the equipment it controls, and it switches either line voltage or a dry contact. That makes relays the right tool for keeping designer switches, automating garage doors and gates, and bringing boilers, pumps and sprinklers onto a Zigbee or Z-Wave hub.

Our top pick: Zooz ZEN51 Dry Contact Relay. Runner-up: Zooz ZEN17 800LR Universal Relay.

Every pick below assumes a neutral wire at the install point or a low-voltage power supply, the normal setup for full-featured relay modules. The five picks cover one in-wall Z-Wave relay for lighting, two multi-contact Z-Wave relays for doors and equipment, and two Zigbee modules, one with metering and one built purely for dry-contact jobs.

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

Start with the Zooz ZEN51 if you want one light circuit on Z-Wave behind the switch you already own. Pick the Zooz ZEN17 for garage doors, gates and boilers that need dry contacts, the ZEN16 when three separate contacts share one project, the Aqara T2 for a Zigbee two-channel module with metering, and the MHCOZY 1-Channel for a single budget dry contact.

Zooz ZEN51 Dry Contact Relay

The ZEN51 is the classic behind-switch Z-Wave relay. It wires in behind your existing mechanical switch or up at the light fixture, takes over on and off control, and leaves the wall switch working as a manual input. Because the output is a dry contact rather than a powered terminal, the same module can also pulse a low-voltage input or report when a 120 V signal appears on its input side.

Zooz builds it on a 700 series Z-Wave chip with Long Range, S2 security and SmartStart pairing, so setup on hubs such as SmartThings, Hubitat and Home Assistant is mostly a QR scan. It supports single-pole and 3-way wiring, multi-tap scene triggers on hubs that expose them, and a smart bulb mode that keeps power flowing to smart bulbs while the wall switch sends commands instead. It is a mains-powered mesh repeater and is ETL listed. The trade-offs: it needs a neutral wire, it is on and off only, and it reports no energy data. This is a mid-range, everyday retrofit module.

Specs

    • Model: ZEN51
    • Wireless protocol: Z-Wave Plus, 700 series, Long Range, S2 SmartStart
    • Power: 100-240V AC, 50/60Hz (neutral wire required)
    • Maximum load: 150W LED or CFL, 960W incandescent, 10A resistive, 1/2 HP motors
    • Output type: dry contact (normally open)
    • Dimensions: 1.5 x 1.4 x 0.7 inches
    • Hub: required (Z-Wave hub, sold separately)

    Zooz ZEN17 800LR Universal Relay

    Where the ZEN51 is a lighting relay first, the ZEN17 is an equipment relay. It carries two independent dry contact outputs, and each output gives you both a normally open and a normally closed terminal, so it can start a device by closing a circuit or stop one by opening it. That NO and NC choice makes it the standard pick for garage doors, gates, awnings, fireplaces, sprinklers and boiler calls for heat.

    The current 800LR version runs an 800 series Z-Wave chip with Long Range and acts as a signal repeater. Two separate inputs accept dry contact signals or 12 to 24 V wet inputs, monitored independently of the outputs, so a door sensor or float switch can report through the same module that fires the opener. Power comes from a 12 to 24 V supply or a USB C plug; a USB C cable is included, the adapter is not. Zooz notes it is not supported by Wink or alarm panels. A mid-range module with a premium feature set for anyone wiring more than lights.

    Specs

      • Model: ZEN17 800LR
      • Wireless protocol: Z-Wave, 800 series, Long Range, S2 SmartStart
      • Channels: 2 independent dry contact relays
      • Maximum load: 20A on normally open contacts, 10A on normally closed contacts
      • Inputs: 2, dry contact or 12-24 V, monitored separately from outputs
      • Power: 12-24 V AC/DC or USB C (adapter not included)
      • Hub: required (Z-Wave hub; not supported by Wink or alarm panels)

      Zooz ZEN16 MultiRelay

      The ZEN16 answers a different question: what if one location needs three relays? A single MultiRelay gives you three independent dry contacts, rated 15 amps, 15 amps and 20 amps, enough for two garage doors plus a gas fireplace, or sprinklers, landscape lighting and a pool pump from one unit near the equipment.

      It runs on 12 to 24 V AC/DC or a USB C supply, so no neutral wire is involved, and each relay has its own optional switch input for local control. Built-in per-relay timers simplify automations such as momentary garage door pulses, and the module restores relay states after a power failure. Zooz notes it does not fully work with Wink or alarm panels, and you supply the power adapter and jumper wires yourself. This is the mid-range workhorse for multi-contact projects.

      Specs

        • Model: ZEN16 (current 800LR version)
        • Wireless protocol: Z-Wave Plus, S2 security, SmartStart, Long Range on the current version
        • Channels: 3 independent dry contact relays
        • Maximum load: 15A relay 1, 15A relay 2, 20A relay 3
        • Power: 12-24 V AC/DC or USB C 5V (power supply not included)
        • Hub: required (Z-Wave hub; limited support on Wink and alarm panels)

        Aqara Dual Relay Module T2

        The T2 is the Zigbee entry in this roundup and the most switch-like of the five. It is a two-channel module that installs in a wall box or at the fixture, keeps your existing switch working, and can run its contacts in either wet mode, passing power to the load, or dry mode, where the contacts simply close a circuit for a garage door opener, gate or boiler.

        Aqara adds power metering, which none of the Zooz relays here offer: the module reports the consumption of the connected loads, useful for confirming a pump or heater actually ran. It speaks Zigbee 3.0 and needs an Aqara hub for the full feature set, which then bridges it to the major voice and home platforms. It accepts a wide power range, line voltage AC or low-voltage DC, giving installers flexibility in equipment cabinets as well as switch boxes. It sits mid-range, and suits Zigbee households that want one module to cover both a light circuit and a dry-contact job.

        Specs

          • Wireless protocol: Zigbee 3.0
          • Channels: 2 independent relays
          • Power: AC 100-250V, 50/60Hz, or DC 24-60V
          • Maximum load: 10A per channel
          • Power metering: yes, reports consumption of connected loads
          • Hub: Aqara Zigbee hub required for full features

          MHCOZY 1-Channel ZigBee Smart Relay Switch

          The MHCOZY 1-Channel is the budget, single-job module of the group. It is a small board-style relay with one clean dry contact (normally open, common and normally closed terminals) and two working modes: self-locking, where the contact stays on or off like a normal switch, and momentary inching, where it closes for about a second and releases, the pulse a garage door opener, gate controller or door strike expects.

          Power is flexible: feed it from a USB 5V source or directly from 85 to 250 V AC, which makes it easy to mount beside an opener and borrow its power. It speaks Zigbee 3.0, pairs with common Zigbee hubs and coordinators, and supports an optional 433 MHz remote on this model family. There is no power metering and the documentation is thinner than the brand-name modules, so it suits confident DIY installers. As the budget pick, it is the simplest way to add one dry contact to a Zigbee network.

          Specs

            • Model: ZG002RF
            • Wireless protocol: Zigbee 3.0
            • Channels: 1 dry contact relay
            • Contact terminals: normally open, common, normally closed
            • Relay rating: 10A
            • Power: USB 5V or AC 85-250V
            • Hub: required (Zigbee hub or coordinator)

            How to Choose

            Start with the load, not the radio. If the module will switch a light or fan directly, you need a line-voltage or wet-contact relay sized for the circuit, such as the ZEN51 behind a switch or the Aqara T2 in wet mode. If it will trigger equipment that has its own power, a garage door opener, gate, boiler or door strike, you need a dry contact, and the ZEN17, ZEN16 and MHCOZY are built for that.

            Next, count contacts and check for normally closed wiring. Most projects need normally open contacts only, but fail-safe setups and some awnings need a contact that opens on command. Only the ZEN17 and MHCOZY give you both NO and NC terminals; the ZEN16 wins at three contacts in one place.

            Then check power at the install point. In-wall modules such as the ZEN51 and the T2 need a neutral wire in the box or at the fixture. The ZEN17 and ZEN16 sidestep the switch box by running on a low-voltage supply or USB C power near the equipment. Finally, match the radio to your hub: Zooz needs Z-Wave, Aqara and MHCOZY need Zigbee, and none of these modules reach a phone or voice assistant without that hub.

            Who Should Skip

            Skip this whole category if your switch boxes have no neutral wire and you cannot reach one at the fixture; no-neutral retrofits are a different product class. Skip relays if you want dimming, since every module here is on and off only, and look at smart dimmer switches instead. Skip DIY boards such as the MHCOZY if you are not comfortable wiring mains or low-voltage equipment, and hire an electrician for anything inside a panel. Finally, skip dry-contact relays for plug-in loads; a smart plug is simpler.

            FAQ

            Do these relay modules need a hub?

            Yes. The Zooz modules need a Z-Wave hub, the Aqara T2 needs an Aqara Zigbee hub for its full feature set, and the MHCOZY needs a Zigbee hub or coordinator. Voice assistants and phones reach the relays through the hub, not directly.

            What is the difference between a dry contact and a normal relay output?

            A normal output passes power through to the load, the way a light switch does. A dry contact is an isolated switch closure with no voltage of its own, so the equipment on the other side uses its own power. Garage door openers, gates and boilers expect a dry contact.

            Can I keep using my existing wall switch with a relay module?

            With the in-wall modules, yes. The ZEN51 and the Aqara T2 wire your current mechanical switch to an input, so the switch keeps working by hand while the hub controls the same load. The ZEN16 and ZEN17 also accept optional switch inputs for local control.

            Will a relay work in a 3-way switch setup?

            The ZEN51 supports single-pole and 3-way wiring with mechanical switches, one reason it is the default lighting pick here. Confirm the wiring diagram for your layout before ordering, and never connect these relays to a wall dimmer or an electronic add-on switch.

            Final Verdict

            For one light circuit on Z-Wave, the Zooz ZEN51 is the straightforward pick: small, ETL listed, and happy in 3-way setups. For equipment, the ZEN17 covers the widest range of dry-contact jobs with its NO and NC contacts and sensor inputs, while the ZEN16 is the efficient answer when three contacts live in one place. Zigbee homes should look at the Aqara T2 for a two-channel module with metering, or the MHCOZY 1-Channel when one dry contact on a budget is all the project needs.

            Product and ASIN Reference

            Product ASIN
            Zooz ZEN51 Dry Contact Relay B0B5VR87JX
            Zooz ZEN17 800LR Universal Relay B096LLL1C6
            Zooz ZEN16 MultiRelay B0846DZJD8
            Aqara Dual Relay Module T2 B0CC2B8C37
            MHCOZY 1-Channel ZigBee Smart Relay Switch B0BRJM21CG
            T
            TechVentureSpot Editorial Team
            We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best Zigbee and Z-Wave Smart Relays and In-Wall…Check price on Amazon

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free
            Prime for Young Adults

            A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

            See Prime for Young Adults
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free

            As an Amazon Associate we earn from qualifying purchases.